Service Tips


Scissor lift accidents spur osha to issue hazard warning

Mar 28, 2016 David Sparkman | MHLnews
Over a one-year period OSHA found 10 fatalities and 20 serious injuries involving scissor lifts.
A spate of accidents involving scissor lifts has caused the Occupational Safety and Health Administration (OSHA) to issue a hazard alert outlining employers’ obligations and preventive measures.

Scissor lifts aren’t just used in warehousing; they also are common in the construction, retail, entertainment and manufacturing industries, among others.

OSHA points out that over a one-year period it had investigated 10 fatalities and more than 20 other serious injuries it termed preventable involving scissor lifts. OSHA says it found that most of these injuries and fatalities were the result of employers not properly addressing fall protection, stabilization and positioning.

OSHA reminds employers that only trained workers should be allowed to use scissor lifts, and employers should make sure that those workers show that they can use a scissor lift properly.

Training must at a minimum include manufacturer’s instructions for operating and moving the lift, handling materials on the lift, including weight limits, and other worksite hazards workers could encounter, such as contact with electrical wires. OSHA stresses that training must cover reporting any equipment defects or maintenance needs.

Employer obligations include making sure the equipment is properly maintained, manufacturer’s instructions are followed, personal protective equipment is worn, and safe work practices are practiced.

To avoid falls, lift platforms must have guardrails, and employees should be trained to check to make sure a guardrail is in place, only stand on the work platform, never stand on the guardrails, and keep work within easy reach to avoid leaning away from the lift.

To assure stabilization OSHA notes that manufacturer instructions for safe movement usually rule out moving the lift in an elevated position. Isolate the scissor lift or implement traffic control measures to ensure that other equipment cannot contact the scissor lift, the agency says. Also select work locations with firm, level surfaces away from hazards that can cause instability, such as drop-offs, holes, slopes, bumps, ground obstructions, or debris.

Use the scissor lift outside only when weather conditions are good, OSHA adds, noting that scissor lifts rated for outdoor use are generally limited to wind speeds of less than 28 miles per hour.

OSHA cites the example of a student employee of the University of Notre Dame who was killed in 2010 while filming a football practice from a scissor lift. Untrained, he chose to raise the lift more than 39 feet, and winds gusting more than 50 miles per hour blew the lift over.

“Positioning the scissor lift to avoid electrocution, arc flash and thermal burns is important for safely using scissor lifts near energized power lines,” OSHA warns. “Since electricity can arc or jump from the power line to the scissor lift or worker, electrocution can occur even if neither the scissor lift nor the worker touches the power line.”

Although rare, the collapse of scissor lifts can be prevented if employers ensure that safety systems designed to stop collapsing are maintained and not bypassed. Never allow the weight on the work platform to exceed the manufacturer’s load rating. Never allow equipment other than the scissor mechanism to be used to raise the work platform—including using a forklift to lift it.

“Scissor lifts provide a safe and reliable platform for workers to perform job tasks when used according to the manufacturer’s instructions,” OSHA says. “When not used properly, scissor lifts can present a serious hazard to workers. Employers are responsible for keeping workers safe.”


Small Engine Gas Notice

06/23/2014




Tire Damage on Lifts

03/01/2014

A common question heard, “When should a damaged tire be replaced?”  The following is a guideline that will help you make that decision.

Pneumatic Tires:  
If there are any cuts, rips or tears that expose sidewall or tread area cords in the tire, remove the tire from service immediately.  Arrangements must be made for replacement of the tire or tire assembly.

Polyurethane foam filled tires:

Remove the tire from service immediately and make arrangements for replacement of the tire or tire assembly when any of the following conditions are discovered:

  • A smooth, even cut through the cord plies which exceeds 3 inches in total length

  • Any tears or rips (ragged edges) in the cord plies which exceeds 1 inch in any direction

  • Any punctures which exceed 1 inch in diameter

  • Any damage to the bead area cords of the tire

If a tire is damaged but is within the above noted criteria, the tire must be inspected on a daily basis to insure the damage has not propagated beyond the allowable criteria.

Sioux Falls, SD 605-332-4466

Rapid City, SD 605-348-6440

Dickinson, ND 701-483-3184

Fargo, ND 701-492-0855

Sioux City, IA 712-252-0640

Connect with Us
Interested in New Products and Promotions?