Materials & Supplies
Manufacturer
W.R.Meadows
Rental
No
Comments
PROTECTION COURSE is a multi-ply, semi-rigid core composed of a mineral-fortified asphalt core formed between two outside layers of asphalt-impregnated reinforced mats, manufactured in accordance with ASTM D 6506.


When properly applied by personnel trained in good waterproofing techniques, PROTECTION COURSE will absorb the impact of aggregate shock and normal jobsite foot traffic. It also protects the membrane waterproofing from penetration by sharp aggregate during backfilling and later settlement. PROTECTION COURSE is available in two types: PC-2, Standard Duty and PC-3, Heavy Duty. Both types are economical and convenient to use.


USES
PROTECTION COURSE is used in between slab construction, such as plaza decks, roof terraces, promenade decks, pedestrian concourses, tunnels, bathroom floors, showers, kitchens, mechanical rooms, parking garage decks, planter boxes, reflective pools, and foundation walls. PROTECTION COURSE is compatible with most currently popular dampproofing and waterproofing materials.


FEATURES/BENEFITS
Tough, durable and lightweight u0085 panels are easily handled, quickly installed.
Full width fiberglass matting improves flexural strength.
Highly resistant to chemical action.
Performance is equally effective in above- or below-grade installations.
Unique dual facing offers compatibility with most currently popular waterproofing materials.
Economical and convenient to use.


PACKAGING
4? x 8? (1.22 m x 2.44 m) Panels


TECHNICAL DATA
ASTM D 6506, Class B
PROTECTION BOARD REQUIREMENTS




APPLICATION
NOTE: Prior to application, consult the waterproofing manufacturer to determine whether the polyethylene film facing on one side, or the asphalt-impregnated reinforced mat on the other side of PROTECTION COURSE, is approved as u0093compatibleu0094 to the specific waterproofing product being protected.


PROTECTION COURSE is installed to form a continuous protective layer over the membrane waterproofing. The sheets can be easily cut with a rooferu0092s knife for fitting at protrusions.


Surface Condition u0085 The waterproofing membrane must be free of sharp projections, dirt, and dust. If water testing is desired, it should be made prior to placing PROTECTION COURSE. Note: PROTECTION COURSE should be applied at the end of each dayu0092s waterproofing to both horizontal and vertical surfaces.


Horizontal Surfaces u0085 PROTECTION COURSE should be installed over the waterproofing membrane as soon as permissible by the membrane applicator or manufacturer. PROTECTION COURSE sheets should be butted together and cut to fit all intersecting surfaces and protrusions. If desired, joints may be covered with DETAIL STRIP from W. R. MEADOWS or rooferu0092s glass reinforced tape embedded in hot asphalt as a secondary waterproofing system. (See PRECAUTIONS.)


Vertical Surfaces u0085 For dampproofed and/or waterproofed vertical walls to receive backfill, PROTECTION COURSE should be butt jointed and, if necessary, temporarily held in place while backfilling.


Backfilling u0085 Backfilling against vertical walls should be done immediately using care and caution to avoid damaging the waterproofing application. Backfill material should not be dropped against PROTECTION COURSE in such a manner that it could drag the sheet down as the backfill drops. For horizontal applications, the waterproofing and PROTECTION COURSE should be installed just prior to the installation of the wearing surface.


PRECAUTIONS
Where PROTECTION COURSE is adhered to a waterproofing membrane, use an approved adhesive. Where taped joints are desired with tape set in hot asphalt, consult membrane manufacturer. PROTECTION COURSE is shipped on pallets with the polyethylene anti-stick sheet on the top or exposed side. PROTECTION COURSE should be stored on pallets and placed on a level surface. CAUTION: Do not apply PROTECTION COURSE over liquid waterproofing membranes containing volatile solvents until all of the solvent has evaporated. Consult membrane manufacturer for specific application details prior to placing PROTECTION COURSE. Read and follow application information and precautions. Refer to Safety Data Sheet for complete health and safety information.


LEED INFORMATION
May help contribute to LEED credits:
MR Credit 2: Construction Waste Management
MR Credit 4: Recycled Content
MR Credit 5: Regional Materials

Sioux Falls, SD 605-332-4466

Rapid City, SD 605-348-6440

Dickinson, ND 701-483-3184

Fargo, ND 701-492-0855

Sioux City, IA 712-252-0640

Connect with Us
Interested in New Products and Promotions?