Materials & Supplies
EVAPRE evaporation retardant is an economical, high quality, water-based compound. It is specifically designed to form a thin monomolecular film to reduce rapid moisture loss from the concrete surfaces prior to curing. EVAPRE provides a significant aid in producing high-quality concrete flatwork. Rapid evaporation of water is retarded, slab surface conditions are normalized, and workers can adhere more closely to established finishing schedules. EVAPRE is also VOC-compliant.
EVAPRE significantly reduces plastic shrinkage and cracking, wind crusting, stickiness, and sponginess, which often cause poor and uneven surface texture. These conditions result when the hydration is more rapid than the movement of bleed water to the surface. EVAPRE effectively combats and minimizes the effects of rapid-drying conditions such as low humidity, low dew point, high winds, direct sunlight, hot weather, heated concrete, or placement of concrete in a heated enclosure or interior area during cold weather. The protective film shield disappears as soon as the concrete is no longer plastic.

EVAPRE is ideal for use as an evaporation retardant for concrete surfaces where the evaporation rate exceeds the rate of bleeding. EVAPRE can be used with the MEADOW-PATCHu00ae and MEADOW-CRETEu00ae line of repair mortars from W. R. MEADOWS. It can also be used with condensed silica fume concrete, concrete containing fly ash, and most other cementitous products. When applying surface hardeners, EVAPRE can be used after screeding and after the first floating operation, if necessary.
NOTE: EVAPRE is specifically designed to fight off the destructive effects of early rapid evaporative moisture loss. Early rapid evaporative moisture loss is addressed in ACI Committee 305R-91, entitled u0093Recommended Practice for Hot Weather Concreting.u0094 This report contains a chart on page five that depicts the effect of concrete and air temperatures, relative humidity, and wind velocity on the rate of evaporation of surface moisture from concrete. It provides a graphic method for estimating the loss of surface moisture for various weather conditions.

Significantly reduces plastic shrinkage and cracking caused by evaporation in low humidity, high temperatures, and high winds.
Allows use of lower slump and lower water: cement ratio concrete.
Provides smooth and durable concrete flatwork.
Reduces wind crusting, stickiness, and sponginess, which often cause poor and uneven surface texture.
Allows finishing crews to adhere to established schedules.
Reduces overall cost because timing of finishing operations is less critical.
Helps minimize surface cracking due to early water loss of silica fume concrete.
Available in exclusive, easy-to-use, 45-ounce containers.

45 Ounce (1,596.9 cm3) Containers
1 Gallon (3.8 Liter) Units
5 Gallon (18.93 Liter) Pails
55 Gallon (208.2 Liters) Drums

One gallon (3.8 liter) of EVAPRE mixed with nine gallons (34.2 L) of water will cover 2000 u0096 4000 ft.2 (50 u0096 100 m2/L). Quantity needed increases if additional coats are required. Forty-five ounce (1596.9 cm3) container u0096 pour into a 3.5 gallon sprayer, add water, and it is ready u00adto use.

When stored indoors and in original, unopened containers at temperatures between 40 u0096 90u00b0 F (4 u0096 32u00b0 C), shelf life is a minimum of one year from date of manufacture.

u0095 Complies with all current federal, state, and local maximum allowable VOC requirements, including U.S. EPA, SCAQMD, and OTC.

STEP 1 u0096 For the majority of applications, EVAPRE should be mixed at a ratio of one (1) part EVAPRE to nine (9) parts water. Agitate EVAPRE before mixing with water. Agitate the diluted solution again, before applying. NOTE: EVAPRE is available in an easy-to-use, exclusive 45-ounce container. Just pour into a 3.5 gallon sprayer, add water to fill, and go to work.
STEP 2 u0096 Apply EVAPRE with a commercial sprayer, such as a Chapin 1949. Use a Chapin 6-5797 or equivalent spray nozzle that produces a flow rate of .5 gallon per minute.
STEP 3 u0096 The EVAPRE diluted solution should be applied immediately after screeding and/or between finishing operations, as needed. Application is simplified by the fugitive pigment, which will disappear completely upon drying. Do not allow puddling. If puddling occurs, wipe up immediately and rinse with water.
STEP 4 u0096 Clean all equipment immediately after use with soap and water.
STEP 5 u0096 Finish concrete surface as required.
STEP 6 u0096 Cure concrete after bleed water or excess surface water has dissipated. The use of EVAPRE does not negate the need for a quality concrete curing or curing and sealing compound from W. R. MEADOWS.
NOTE u0085 The residue remaining on the surface after finishing will not impair bonding or alter color. The protective shield usually lasts as long as the concrete is plastic. Therefore, all concrete surfaces must be properly cured as well.

Keep from freezing. EVAPRE should not be over-applied or worked excessively into the concrete surface during finishing operations. EVAPRE should not be used to re-temper the concrete. EVAPRE is not a curing agent.
W. R. MEADOWS is not responsible for compatibility or results when EVAPRE is used with other manufactureru0092s products.
Read and follow application information and use in accordance with the health and Safety information shown on the container label. Refer to Material Safety Data Sheet for complete health and safety information.

May help contribute to LEED credits:
IEQ Credit 4.2: Low-Emitting Materials: Paints & Coatings
IEQ Credit 4.3: Low-Emitting Materials: Flooring
MR Credit 2: Construction Waste Management
MR Credit 5: Regional Materials


Sioux Falls, SD 605-332-4466

Rapid City, SD 605-348-6440

Dickinson, ND 701-483-3184

Fargo, ND 701-492-0855

Sioux City, IA 712-252-0640

Connect with Us
Interested in New Products and Promotions?